|
|
|
KK2.0 byl navržen od základu tak, aby mohl létat s multicopterami každý.
Díky LCD obrazovce je instalace a nastavení jednodušší, než kdy jindy. Letové typy multi-copter jsou již předinstalovány. Jednoduše vyberete letový typ, zkontrolujete správné rozložení motorů, směr vrtulí, zkalibrujete a můžete letět!
Původní KK gyroskop je nahrazen neuvěřitelně citlivým dvojčipovým 3-osým gyroskopem a jednočipovým 3-osým akcelerometrem. Srdcem KK2.0 je Atmel Mega324PA 8-bit AVR RISC mikroprocesor s 32kB pamětí.
Do KK2.0 byly přidány
|
|
|
|
|
The Multiwii SE V2.0 is a gyro/accelerometer based flight controller that is loaded with features.With expandability options and full programmability, this device can control just about anytype of aircraft. This is the ideal flight controller for your multi-rotor aircraft.
Features:
Small size, 35x35mm mounting holes
6 input channels for standard receiver and PPM SUM receiver
Up to 8-axis motor output
2 servos output for PITCH and ROLL gimbal system
Can utilize a servo output t
|
|
|
|
|
FlyCam MCFC Sets
Specification:
FlyCam MCFC
FlyCam MCFC board
USB to Serial
Jumper cable (8 pieces)
LED/Buzzer
FlyCam GPS/Compass
FlyCam GPS/Compass board
External GPS module
100mm GPS module connecting cable x 2
Vibration Damper M3x15 (4 pieces)
PCB Support 50mm (4 pieces)
PCB Support 10mm (4 pieces)
|
|
|
|
|
FY-901 je inerciální stabilizační systém pro multikoptéry. Díky současné instalaci tříosého gyroskopu a tříosého akcelerometru nabízí tato řídící deska pokročilé řešení "vše v jednom" pro velmi stabilní let jakékoliv multikoptéry!
FY-901 nabízí dva letové režimy, které mohou být přepínány pomocí RC soupravy i během letu:
Auto-stabilizační režim: V tomto režimu je využívaný tříosý akcelerometr pro autostabilizaci modelu tak, aby ramena multikoptéry byla vždy v jejich neutrální poloze. Tento režim je skvělý pro po
|
|
|
|
|
The Arduino Sensor Shield V5.0 allows plug and play connection to various modules
like sensors, servos, relays, buttons, potentiometers and more.
Features:
I2C interface
Bluetooth module communication interface
SD card module communication interface
APC220 wireless RF modules communication interface
RB URF V1.1 ultrasonic sensors interface
12864 LCD serial and parallel interface
32 servo control
|
|
|
|
|
For entry-level enthusiasts, DJI now brings out the most cost-effective solution, the NAZA-M Lite flight control system. As the simplified version of NAZA-M, it inherits the high reliability and stability of NAZA-M in a basic package offering a very competitive price. The innovative All-in-One design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller
|
|
|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
The NanoWii is a complete multi-rotor flight controller. It is based on the ATmega32U4, whichis the processor of the Arduino Leonardo and incorporates a MPU-6050 chip, which is a combinedgyro and accelerometer.
This is the ultimate solution for powerful flight performance with your multi-rotor project,especially micro size models. The possibilities are endless with the NanoWii,only limited by y
|
|
|
|
|
This new version of the ArduPilotMega 2.5 system features a newly designed enclosure and Power Module with integrated 5.3V regulator and current and voltage sensing.
The ArduPilot Mega 2.5 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition.This version is ready to use, with no assembly required.It allows the
|
|
|
|
|
Hobbyking i86L Multi-Rotor Control Board (Lite Edition) features the same level of stability and ease of setup as the standard i86. The i86L features a basic set of multi-rotor layouts and an easy ESC and and stick centering calibration mode via the dip switches.
Controlled by an Atmel Mega168PA 8-Bit RISC based micro controller and utilizing a single 3-axis MEMS gyro the Hobbyking i86L Multi-R
|
|
|
|
|
Pixhawk PX4 2.4.5 32 bit ARM Flight Controller & NEO-6M GPS/4G TF Card/Led External/PPM/PM Module/433 DTM for RC Multicopter
Description:
PIXHAWK intergrated the newest 32 bit chip technology and sensor technology, get rid of the dilemma of having only 8 bit CPU of APM, and CPU occupancy being too high
Features:
with external LED -Dual Size full angle LED
Advanced 32 bit ARM CortexM4 high pe
|
|
|
|
|
This is a mini Arduino based on-screen display board.
Its tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible.
It main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader,
and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin cable.
It features two independent power and ground sections to isolate the OSDs analog stage: a +5V section for the ATmega and th
|
|
|
|
|
For entry-level enthusiasts, DJI now brings out the most cost-effective solution, the NAZA-M Lite flight control system. As the simplified version of NAZA-M, it inherits the high reliability and stability of NAZA-M in a basic package offering a very competitive price. The innovative All-in-One design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis
|
|
|
|
|
Autopilot ZeroUAV YS-X6 je vysoce výkonný a kvalitní řídící systém pro multikoptéry podporující operační systémy Android/IOS a PC systémy, který zaručuje perfektní navigaci, držení směru k cíli, autostabilizaci a udržování polohy a výšky. Je navržený pro profesionální i hobby aplikace, pro nasazení v komerčních a průmyslových platformách. YS-X6 přebírá klasickou ARM+FPGA strukturu, která integruje vysoce přesné senzory, aplikuje pokročilou kompenzaci teplotních rozdílů a průmyslový výpočetní aparát podporovaný velmi rych
|
|
|
|
|
The Phantom 2 features the same compact, highly integrated design as the Phantom one, but comes with FPV flying and aerial cinematography support right out of the box. It is unbelievably easy to fly. Combined with smooth, stabilized footage from the optional H3-2D gimbal, aerial cinematography has never been easier. Its light, rugged and perfect for travel.
The Phantom 2 has an intelligent, hig
|
|
|
|